tkmtechs

  • Quality and Certifications: An ISO Certified Fabrication Company in UAE

    TKM Technical Services LLC is an ISO certified fabrication company in UAE, holding ISO 9001, 14001 and 45001 certificates issued by ASCB and valid to 22 May 2027.
    Every tank, pipe spool and machine we build is inspected, tested and documented before it leaves our Sharjah workshop.

Quality · Environment · Health & safety · Issued by ASCB · Valid to 22 May 2027 · Verifiable on IAF CertSearch

Our ISO Certificates

Standard
What it covers
Certificate number
Issuer
Valid to
ISO 9001
Quality management
9001:AE10001506/01/Q
ASCB
22 May 2027
ISO 14001
Environmental management
14001:AE10001506/02/E
ASCB
22 May 2027
ISO 45001
Occupational health and safety
45001:AE10001506/03/H
ASCB
22 May 2027

What Each Certificate Means for Your Project

  • ISO 9001 — Quality Management

    This standard requires written procedures for how work is planned, checked and corrected. For you, it means every job follows the same controlled steps, from drawing approval and material checks to final inspection, with records you can audit.

  • ISO 14001 — Environmental Management

    This standard requires a system to identify and control a company's environmental impact. It matters to buyers whose own sites and supply chains are audited against environmental standards.

  • ISO 45001 — Occupational Health and Safety

    This standard requires a managed approach to workplace safety. It covers our workshop and our site crews, which matters when our team works inside your running plant during installation or shutdowns.

The QA/QC Documentation Pack With Every Job

Certificates describe a system. The documentation pack proves the system was followed on your equipment. Every job ships with:

Document
What it shows
Inspection and test plan (ITP)
Every inspection and test point, agreed before fabrication starts, including points you or your inspector want to witness
Mill test certificates (MTC)
The chemical and mechanical properties of each plate and pipe, from the steel mill
WPS and PQR
The approved welding procedure and the test record that qualifies it
Welder qualification certificates
That each welder is qualified for the procedure used
Hydrostatic test report
The vessel or pipe held pressure without leaks
Dye penetrant test results
Welds checked for surface cracks
Surface finish report
The finish achieved against your specified Ra value
  • Full Material Traceability

    Traceability runs from each plate's heat number on the mill test certificate to the final weld map. If a question ever comes up about a part of your tank or pipeline, we can show which plate it came from, which welder joined it and which check it passed.

How We Inspect and Test

  • Before fabrication — shop drawings approved by you; materials checked against their mill records.
  • During fabrication — welding to approved procedures; stainless steel work kept apart from carbon steel to
    prevent contamination.
  • Before dispatch — hydrostatic, dye penetrant and surface finish tests, recorded and signed.
  • At handover — as-built drawings, test reports and the full documentation pack.
  • Witness Testing and Inspections

    You or a third-party inspector can witness pressure and dye penetrant tests at our Sharjah workshop before dispatch. Tell us your hold points when you place the order and we will build them into the inspection and test plan.

  • Designing for Hygienic Standards

    For dairy and food equipment, we follow 3-A and EHEDG design principles where your specification calls for them: drainable layouts, no dead legs and controlled surface finish. For pharmaceutical equipment, our documentation pack supports your GMP validation. These are design principles we follow, not product certifications.

What Buyers Ask For, by Industry

Industry
What we document and control
Food processing and dairy
Drainable layouts, no dead legs, surface finish against the specified Ra, materials suited to product contact
Beverage and bottling
Hygienic welds, CIP-ready piping and tank internals, pressure test records
Pharmaceutical
Polished surfaces and a documentation pack that supports your GMP validation
Chemical
Material grade chosen for chemical compatibility, with mill certificates for every plate
Oil and gas
NDT and hydrotest reports for carbon steel piping, skids and structures
  • Health, Safety and Environment

    Our ISO 45001 system covers how our people work in the workshop and on your site, including during installation and shutdowns inside running plants. Our ISO 14001 system covers how we identify and control the environmental impact of our work. Both are audited by ASCB alongside our ISO 9001 quality system, so a buyer gets one supplier with all three management systems in place.

  • Grades Confirmed by Mill Records

    We fabricate in SS304, SS316L, duplex stainless steel, mild steel and carbon steel. SS304 suits general food contact, while SS316L is used where chlorides, acids or strict hygiene apply. Whatever the grade, the mill test certificate confirms the chemistry of each plate and pipe before it is cut, and that record stays in your documentation pack.

  • Warranty and After-Sales Support

    Every fabricated item carries a 12-month warranty on workmanship and materials from handover, stated in each quotation. We keep your drawings and inspection records on file and supply spare gaskets, seals and valves.

How to Check Any Supplier's ISO Certificate

Before you approve a fabrication vendor, check four things:

  • Company name — the legal name shown matches the company quoting you.
  • Certificate number and issuer — the number can be found on the issuer’s register or on IAF CertSearch.
  • Expiry date — the certificate is valid for the full period of your project.
  • Scope — the activities listed cover the work you are buying, such as fabrication and installation.

Also check that the issuer is an accredited certification body. A logo on a website is not proof. A certificate number you can look up is. That is why, as an ISO certified fabrication company in UAE, we publish ours in full on this page.

Quality and Certification FAQs

Yes. TKM Technical Services LLC is an ISO certified fabrication company in UAE, holding ISO 9001, 14001 and 45001, all issued by ASCB and valid to 22 May 2027.

Search the numbers on this page in the IAF CertSearch register, or ask us for PDF copies.

An inspection and test plan, mill test certificates, WPS and PQR, welder qualification certificates, and hydrostatic, dye penetrant and surface finish reports.

Yes. Pressure and dye penetrant tests can be witnessed at our Sharjah workshop before dispatch.

It means work follows written, audited procedures for planning, inspection and correction, so quality does not depend on one person.

Yes. Drawings, inspection records and the documentation pack stay on file for servicing and future work.

Yes. All three are valid to 22 May 2027, and their status can be checked at any time on IAF CertSearch.

We design to 3-A and EHEDG principles where specified. We do not claim product certification under those schemes.

factory-design

Need a Documented, Inspected Build?

Work with an ISO certified fabrication company in UAE that documents every step. Send your drawing and your required documents and hold points. Our engineers will reply within one working day with a quotation that lists the documents and checks included.

Scroll to Top